techpack/smartline/locale/smartline.zh_CN.tr
2022-11-25 17:25:48 +08:00

42 lines
3.0 KiB
Plaintext
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

# textdomain: smartline
SmartLine Button/Switch=SmartLine 按钮/开关
switch,button 2s,button 4s,button 8s,button 16s=开关,按钮 2秒按钮 4秒按钮 8秒按钮 16秒
Insert destination block number(s)=插入目标方块编号
SmartLine Button=SmartLine 按钮
connected with block=已经与方块相连
Node numbers to read the states from:=从以下位置读取状态的节点号:
Node number to send the events to:=要将事件发送到的节点号:
Send an event if state is equal or larget than:=如果 state 等于或大于以下值,则发送事件:
SmartLine State Collector=SmartLine 状态采集器
Save=保存
SmartLine Display=SmartLine 显示器
Input the number(s) of the receiving node(s).=输入接收节点的编号。
Separate numbers via blanks, like '0123 0234'.=通过空格分隔数字如“0123 0234”。
Input the player name(s) separated by blanks,=输入以空格分隔的玩家名称,
or leave it blank for all players.=或者为所有玩家留空。
Player Detector Help=玩家检测器帮助
Player Detector=玩家检测器
Receiver node numbers:=接收器节点号:
Player name(s):=玩家名称:
SmartLine Player Detector=SmartLine 玩家检测器
Destination node numbers=目标节点编号
SmartLine Repeater=SmartLine 中继器
not connected=未连接
connected with=连接到
fault (overloaded)=故障(过载)
Offset/s=偏移量/秒
Run endless=无休止运行
SmartLine Sequencer=SmartLine 序列器
stopped=已经停止
running=正在运行
SmartLine Sequencer Help@n @nDefine a sequence of commands to control other machines.@nNumbers(s) are the node numbers, the command shall sent to.@nThe commands 'on'/'off' are used for machines and other nodes.@nOffset is the time to the next line in seconds (1..999).@nIf endless is set, the Sequencer restarts again and again.@nThe command ' ' does nothing, only consuming the offset time.@n=SmartLine 序列器 帮助@n @n定义一系列命令来控制其他机器。@nNumbers(s) 是节点编号,命令将会发送到(这个节点)。@n命令“on”和“off”用于机器和其他节点@n偏移量是到下一行的时间以秒为单位 (1..999)。@n如果设置了 endless无休止序列器会一次又一次地重新启动。@n命令“ ”不执行任何操作,仅消耗偏移时间。@n
Number(s)=编号
Command=命令
help=帮助
close=关闭
SmartLine Signal Tower=SmartLine 信号塔
Time=时间
SmartLine Timer=SmartLine 计时器
SmartLine Timer Help@n@nThe Timer is for a daytime controlled sending of commands@ne.g. to turn street lights on/off. The timer checks the @ntime every few seconds. If the block was just loaded, @nthe timer will check the last 4 hours for commands@nthat still need to be executed.=SmartLine 计时器帮助@n@n计时器用于在白天发送控制命令@n例如打开、关闭路灯。@n计时器会每隔几秒钟检查一次时间。@n如果方块刚刚加载计时器将会@n检查最后四个小时内仍然需要执行的命令。